ASUS RAMPAGE V EXTREME/U3.1 Specifications:
CPU:
- Intel Socket 2011-v3 Core i7 Processors
- Supports Intel 22 nm CPU
- Supports Intel Turbo Boost Technology 2.0
The Intel Turbo Boost Technology 2.0 support depends on the CPU types.
Chipset:
- Intel X99
Memory:
- 8 x DIMM, Max. 64GB, DDR4 3300(O.C.)/3000(O.C.)/2800(O.C.)/2666(O.C.)/2400(O.C.)/2133 MHz Non-ECC, Un-buffered Memory
- Quad Channel Memory Architecture
- Supports Intel Extreme Memory Profile (XMP)
- Hyper DIMM support is subject to the physical characteristics of individual CPUs.
Multi-GPU Support:
- Supports NVIDIA 4-Way SLI Technology
- Supports NVIDIA 3-Way SLI Technology
- Supports NVIDIA SLI Technology
- Supports AMD 4-Way CrossFireX Technology
- Supports AMD 3-Way CrossFireX Technology
- Supports AMD CrossFireX Technology
Expansion Slots:
- 4 x PCIe 3.0/2.0 x16 (x16, x16/x16, x16/x8/x8 or x16/x8/x8/x8 mode with 40-LANE CPU; x16, x16/x8, x8/x8/x8 mode with 28-LANE CPU)
- 1 x PCIe 2.0 x16 (x4 mode)
- 1 x PCIe 2.0 x1
Storage:
- New Intel Core i7 Processors :
1 x M.2 Socket 3, , with M Key, type 2260/2280/22110 storage devices support ( Supports PCIE SSDs only)
- Intel X99 chipset :
1 x SATA Express port, red, compatible with 2 x SATA 6.0 Gb/s ports
8 x SATA 6Gb/s port(s), red
Supports Intel Smart Response Technology, Intel Rapid Recovery Technology
- ASMedia SATA Express controller :
1 x SATA Express port, red, compatible with 2 x SATA 6.0 Gb/s ports
LAN:
- Intel I218V, 1 x Gigabit LAN Controller(s), featuring GAMEFIRST III
- Intel LAN- Dual interconnect between the Integrated LAN controller and Physical Layer (PHY)
- Anti-surge LANGuard
Wireless Data Network:
- Wi-Fi 802.11a/b/g/n/ac
- Supports dual band frequency 2.4/5 GHz
- Up to 1300Mbps transfer speed
Bluetooth:
- Bluetooth V4.0
Audio:
- ROG SupremeFX 8-Channel High Definition Audio CODEC
Supports : Jack-detection, Multi-streaming, Front Panel Jack-retasking
SupremeFX Shielding Technology
ELNA premium audio capacitors
USB Ports:
- Intel X99 chipset
4 x USB 3.0 port(s) (4 at mid-board)
- Intel X99 chipset
6 x USB 2.0 port(s) (2 at back panel, black, 4 at mid-board)
- ASMedia USB 3.0 controller
10 x USB 3.0 port(s) (10 at back panel, blue)
OC Panel:
2.6 " LCM display
EXTREME/NORMAL mode switch
- EXTREME Mode for subzero OC benching
VGA Hotwire
Subzero Sense
Slow Mode
Pause Switch
VGA SMB header
ProbeIt
4 x 4-pin extra fan connectors
- NORMAL Mode for in-chassis usage
CPU Level Up OC button
FanSpeed control button
LCM backlight on/off button
- I/O Ports
POWER:1 x SATA power connector
ROG_EXT port:1 x 18-1 pin data connection port
Back I/O Ports:
- 1 x PS/2 keyboard/mouse combo port(s)
- 1 x LAN (RJ45) port(s)
- 10 x USB 3.0 (blue)
- 2 x USB 2.0 (one port can be switched to ROG Connect)
- 1 x Optical S/PDIF out
- 5 x Audio jack(s)
- 1 x Clear CMOS button(s)
- 1 x ROG Connect On/ Off switch(es)
- 1 x ASUS Wi-Fi GO! module (Wi-Fi 802.11 a/b/g/n/ac and Bluetooth v4.0
Internal I/O Ports:
- 2 x USB 3.0 connector(s) support(s) additional 4 USB 3.0 port(s)
- 2 x USB 2.0 connector(s) support(s) additional 4 USB 2.0 port(s)
- 2 x SATA Express connector: red, with M key, type 2242/2260/2280 storage devices support (both SATA & PCIE mode)
- 1 x M.2 Socket 3 for M Key, type 2260/2280/22110 storage devices support ( Support PCIE SSD only)
- 1 x TPM header
- 8 x SATA 6Gb/s connector(s)
- 1 x CPU Fan connector(s) (1 x 4 -pin)
- 1 x CPU OPT Fan connector(s) (1 x 4 -pin)
- 6 x Chassis Fan connector(s) (6 x 4 -pin)
- 1 x Thunderbolt header(s)
- 1 x 24-pin EATX Power connector(s)
- 1 x 8-pin ATX 12V Power connector(s)
- 1 x 4-pin ATX 12V Power connector(s)
- 1 x Front panel audio connector(s) (AAFP)
- 1 x System panel(s) (Q-Connector)
- 1 x MemOK! button(s)
- 1 x Slow Mode switch(es)
- 9 x ProbeIt Measurement Points
- 3 x Thermal sensor connector(s)
- 1 x EZ Plug connector(s) (4-pin Molex power connector)
- 1 x Power-on button(s)
- 1 x Reset button(s)
- 1 x BIOS Switch button(s)
- 1 x LN2 Mode jumper(s)
- 1 x ROG extension (ROG_EXT) header(s)
- 1 x KeyBot Button
- 1 x Sonic SoundStage Button
- 1 x Safe Boot button
- 1 x ReTry button
BIOS:
- 2 x 128 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI2.7, WfM2.0, SM BIOS 2.8, ACPI 5.0, Multi-language BIOS, ASUS EZ Flash 2, CrashFree BIOS 3, F11 EZ Tuning Wizard, F6 Qfan Control, F3 My Favorites, Quick Note, Last Modified log, F12 PrintScreen, F3 Shortcut functions and ASUS DRAM SPD (Serial Presence Detect) memory information.
Manageability:
- WfM2.0, DMI2.7, WOL by PME, PXE
Form Factor:
- Extended ATX Form Factor
- 12 inch x 10.7 inch ( 30.5 cm x 27.2 cm )
The Asmedia 106x SATA Host Controller Drive is designed to provide functionality for the following Storage Controllers:
- Asmedia 106x SATA Controller
- Asmedia 106x SATA Controller
Software installation is flexible and fully automated.
Note:
- for X99-Deluxe / X99-S
Installation:
1. If you are installing the operating system on a system configured for RAID or AHCI mode, you must pre-install the Asmedia 106x SATA Host Controller Drive driver using the F6 installation method;
If you are installing this driver on a system configured for IDE mode, you need do the following steps to finish the installing:
a) double-click on the self-extracting and self-installing
setup file and answer all prompts presented
b) enter the following path:
<bootdriver>\Program Files\ASM106xSATA\Driver
you can find a directory named "PREPARE", open it
c) double-click the script "install.cmd"
d) reboot system, and switch to AHCI mode, operating system will automatic installed this driver.
2. To install the Asmedia 106x SATA Host Controller Drive, double-click on the self-extracting and self-installing setup file and answer all prompts presented.
3. By default, all installed files (.inf, .sys, .cat) are copied to the following path:
<bootdrive>\Program Files\ASM106xSATA\Driver
Note: after install complete, you need doing follow steps to keep it work on WIN7 x64 Edition or Win Server 2008 x64 Edition:
3.1 reboot the system
3.2 press F8 on bootup menu
3.3 select "Disable Driver Signature Enforcement", enter ENTER and go on.
About SATA / AHCI / RAID Driver:
When you install an operating system, SATA settings (be it AHCI, RAID, or IDE mode) are detected from the BIOS. If you want to change from one mode to another after the OS has been applied, appropriate drivers are required.
Bear in mind that if you modify these settings without installing proper files first, the operating system will not be able to boot until changes are reverted or required drivers are applied.
To perform the latter task, get the package, run the available setup and follow the instructions displayed on-screen for a complete installation. Afterwards, perform a system reboot so that all changes take effect, enter BIOS menu, and set the SATA option to the mode that best describes the newly applied drivers.
So, if you intend to modify the SATA settings to the mode described by this release, click the download button, and make the desired changes. In addition to that, don’t forget to constantly check with our website so that you don’t miss a single new release.
Comments not found